Serial To Ethernet Converters

Leading Manufacturer of serial to ethernet converter and serial port converter from Pune.

Serial To Ethernet Converter

Get Best Quote

Product Price: Rs 4,000 / PieceGet Best Price

Minimum Order Quantity: 1 Piece

Product Details:

Network Speed	10/100 Mbps
Fiber Type	Single/Multi
Data Rate	10/100Mbps
Usage	Networking
Connector Type	SC
Country of Origin	Made in India

MODBUS TO TCP/IP CONVERTERFeatures : 3-in-1 RS-232/422/485 interface Max.115.2Kbps Serial interface and 10/100 Mbps Ethernet Supports 4- and 2-wire RS-485 with AUTO-SEND™ and built-in terminator Supports industrial 9V DC TO 24 VDC power input and optional Power over Serial Terminal block accessories for easy RS-422/485 serial wiring Supports configuration store and copy for easy deployment Supports Driver, TCP Server/Client Pair Connection operation modes Easy and powerful configuration programTECHNICAL DATAPOWER SUPPLY9 Vdc TO 24V dcPOWER CONSUMPTION1 WINSULATION500VDCLED STATUS INDICATORSPower supplyRX-TX serial communication Ethernet Link and data transferTRANSMISSION RATERS232 from 9600 bps to 115.2 Kbps RS485 from 9600 bps to 115.2KbpsCONSUMPTION ETHERNET PORT< 100maFast Ethernet port 100 TX, RJ45 (TCP/IP)SERIAL PORT1 serial port RS232/RS485INDUSTRIAL PROTOCOLS SUPPORTEDModbus TCP-IP, Modbus RTUMODBUS BRIDGE FUNCTIONFrom Modbus TCP-IP to Modbus RTU From Modbus RTU to Modbus TCP-IPCONFIGURATIONVia WebpageCOMMUNICATION INSTALLATIONDIP switch setting for RS232 & RS485 DIN guidePROTECTION DEGREEIP20OPERATING TEMPERATURE-25..+70°CRS-485/RS-422 TERMINAL PINOUTTERMINALNO.12345RS-485485+485-GNDRS-422TX+TX-RX+RX-GND3.0 DIP SWITCH SETTINGS:DIP SWITCH SETTINGSStatusON-1OFF-2, 3, 4RS 232ON-2OFF-1, 3, 4RS485 2-WIREON-4OFF-1, 2, 3RS422 4-WIRECONNECTION DETAILS1) DB9 MALE RS – 232 2- RX3- TX5- GND2) RS-485 TX+ TX+TX- TX-3) RS-422 TX+ RX+TX- RX-RX+ TX+RX- TX-Configuration and Operation:Assign a static IP address to your computer (eg. 192.168.1.10) and a subnet mask of 255.255.255.0. This is necessary to ensure that, your computer can communicate with Ethernet converter. Primary DNS 8.8.8.8. Secondary DNS8.8.4.4. Computer must have an Ethernet card and TCP/IP installed.TCP/IP should already be installed on computer using Windows 98/2000/XP and later operating systems.Step 1：Open your web browser and type . This address is the factory set IP Address of your PETH converter. Press “Enter” as below shown in an image.Step 2： the setup screen will then appear. You will see the all the configurations and network setting those you have set.MAC Address: At present the device MAC Address & System time Static (or Fixed) IPIP Address: default 192.168.1.20 Subnet mask: default 255.255.255.0 Gateway: default 192.168.1.1 Primary DNS: default 8.8.8.8 Secondary DNS: default 8.8.4.4If you are connecting through a static or fixed IP from your Network environment, perform following steps：Step 1: Enter IP address Step 2: Enter Subnet maskStep 3: Enter Gateway IP address Step 4: Enter Primary DNS IP addressStep 3： Network setting:-If there is a DHCP Server existing in your network environment or you subscribe a CABLE service from your ISP, you can set IP configuration to DHCP to get a Dynamic IP address. 4.6 DHCPHost Name (Optional): default NETUART, maximum Length 15 charactersSystem IP Configuration & Network setting:- In network setting there are 2 mode of communication that you can change , Server- Act as master. Client- Act as Slave.Depend upon your communication DHCP also you can make Disable or Enable.Step 3： Port setting:-You can make PORT setting as shown below in image.Steps as bellow:-1. Port no. 1 :- 10252. Baud Rate:- 9600 to 115200 kbs3. Data Bits:- 84. Parity:- None, Even ,Odd5. Stop Bits:- 1,2Same process you can follow for Port no. 2 i.e 1026

Additional Information: